| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
flag is worth 21%
The obvious question after the last commit was what it did on the actual target. The
answer is nothing, and the useful part is that the same run says what DOES work.
Four builds on the die, 5 document lengths x 7 trials each:
configuration fixed per char at 160 vs base
ReleaseSmall 16.99 ms 54.3 us 25.56 ms 1.00x
ReleaseSmall+lineSpan 17.10 ms 54.0 us 25.63 ms 1.00x
ReleaseFast 14.85 ms 34.7 us 20.30 ms 0.79x
ReleaseFast+lineSpan 14.88 ms 34.2 us 20.25 ms 0.79x
The edit-path change is invisible in BOTH modes, and ReleaseFast+lineSpan is
indistinguishable from ReleaseFast alone. The optimisation mode is the whole of the
difference, which is what Experiment 3 predicted: the edit path is 220 us of a 17 ms
keystroke, so making it cheaper cannot move the total, while the mode makes the
RENDERER faster and the renderer is where the time is.
`experiments/report.typ` gains that table and the reason the four-way comparison
exists rather than four indistinguishable lines on figure 1.
The board is now flashed with the default build, which as of the pin next door means
ReleaseFast: 809,552 B of the 1,536,000 B partition, 53%.
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The board half: the -Dprof attribution that overturned the conclusion, its data, and
the report correction.
`-Dprof` adds two cycle-counter reads around `pardes_p4_input` and
`pardes_p4_render` and prints both. Off by default: it puts a line on the wire per
frame, which is the very resource being measured, so it answers "where did the 15 ms
go" and not "how fast is it".
It answered. Input is flat at ~220 us regardless of document size - 1.5% of a
keystroke - and the entire ~15 ms floor plus every microsecond of the per-character
slope live in `render`. The edit-path fix that the source reading implied (committed
next door in 02-pardes-code) is worth 20% on a 19 MB file and, measured here over 5
conditions x 7 trials, exactly 0% on this board.
`experiments/report.typ` gains Experiment 3 and a correction: Experiment 2's
mechanism claim was wrong, says so, and carries the disproof beside it. The ranked
recommendations are reordered with the renderer at #1.
Also here: `--sweep position` in p4-bench, which holds the document fixed at one
320-character line and moves only the cursor. Column 320 costs 33.9 ms and emits 28
bytes; column 0 costs 26.0 ms and emits 81. Latency and output size are inverted on
this board - the signature of a walk from the start of a line.
|
|
|
"Too slow for interactive use" is a real complaint and not a number. This adds the
number, and the number says the wire is innocent.
## The instrument
`tools/perfproto.zig` is a small framed protocol - "P4", op, length, CRC-32 of the
payload, payload - shared VERBATIM by the host tool and `examples/uartperf.zig`, so
a frame one writes and the other parses cannot drift. It is imported as a module by
both, not copied.
The checksum is the whole point. RX overrun on this UART is undetected in hardware
and uncounted in the driver, so a byte that never arrived is indistinguishable from
a late one; a throughput figure that is not checksummed is a guess about how fast
data was corrupted. `sink` accumulates a CRC over every payload byte the board
received and `report` hands it back, so the host can prove that what arrived is
what it sent.
`tools/rtt.zig` is the two timing functions: `roundTrip` and `measure`. Round trip
is to the FIRST response byte, deliberately. A renderer that starts drawing in 8 ms
and finishes in 130 ms feels immediate; one that thinks for 130 ms and then draws in
8 ms feels broken; waiting for the wire to fall quiet cannot tell them apart. Time
to the last byte is recorded separately as `settle`. Microseconds, because at 115200
one byte is 87 us and a millisecond clock quantises the answer into buckets eleven
bytes wide.
`tools/bench_main.zig` is `p4-bench`: `--link` for the ceiling, `--editor` for how
much of it the editor uses, `--sweep` for one controlled variable at a time with
`--csv` raw per-trial output.
## What it measured
The link is essentially perfect: 11,496 B/s up and 11,413 B/s down, 99.8% of
capacity in both directions, CRC verified over 32,768 B each way, zero corruption.
Typing at 6 to 100 keys/s loses nothing and never uses more than 9% of the wire, so
H5 - "typing loses input" - is refuted.
Latency is compute per input event, not transmission. A 40-byte motion and a
206-byte insert-and-escape cost the SAME round trip to within 0.3 ms, across a
five-fold range of output. That is why raising the baud cannot fix typing: there is
almost no wire in it.
And an edit costs the whole document. Round trip against characters already in the
line is a straight line at 54.3 us per character per keystroke - 17.0 ms at an empty
line, 25.6 ms at 160. On a ~90 MHz core that is ~5,000 cycles per character, far
more than a copy alone, so the full-buffer copy the source does is accompanied by at
least one more full pass.
One controlled intervention: building the editor object ReleaseFast instead of
ReleaseSmall cuts the fixed cost 13% and the per-character cost 36%, for 35% more
flash (809,536 B of a 1,536,000 B partition). Its advantage grows with the document.
Nothing else measured comes close to that ratio.
## Three bugs found while building it
The responder printed garbage and looked dead: it read `.rodata` before evicting the
bootloader's stale cache lines. `flushFlashCache` moved from `src/pardes/app.zig` to
`soc.zig` with its measured evidence, since every application that touches `.rodata`
after hand-over needs it and exactly one file knew that.
Then it booted, printed its marker and went silent after ten seconds:
`rst:0x10 (CHIP_LP_WDT_RESET)`. The bootloader arms the RTC watchdog and expects the
application to take it over. Only the editor ever did.
`serial.Port.drain()` drains INPUT, not output - so timing a transfer to it reported
202% of the wire's capacity and ate the reply. Added `flushOutput` (tcdrain), named
so the two cannot be confused again.
Also: Zig 0.16 emits an explicit `+` for a non-negative SIGNED integer whenever a
width is given (std/Io/Writer.zig:1548-1559), which put a `+` in front of every
number in the first tables.
## The report
`experiments/report.typ` reads the raw CSVs and computes its own figures, so a
re-run changes the document instead of contradicting it. It states five hypotheses,
settles each against one experiment, and is explicit about the one that failed: the
geometry sweep is confounded, because characters accumulated across conditions and
the length experiment then proved that matters. It is reported as unsupported rather
than dressed up as a result.
|
