clipboard, n/N and the tty prompt: three things that were half-wired

Three changes that all turned out to be the same shape -- a feature that
worked in one direction, or for one pane kind, and quietly did not in the
others.

CLIPBOARD. Every register write emitted set_clipboard, so deleting one
character threw away whatever the desktop was holding; multi-cursor yank took
the join's early return and emitted nothing at all, so the same key reached
the clipboard on one cursor and not on two. Nothing could READ the clipboard:
the SDL shell had no SDL_GetClipboardText anywhere in it, and the tty shell
never asked for OSC 52, so `p` from another application was dead in both.

Now it is helix's split. y/d/c/p/P/R and the acme chords are the DEFAULT
REGISTER and nothing else; the system clipboard is five words on helix's own
letters -- SPC y, SPC Y, SPC p, SPC P, SPC R -- spelled as builtins so they
land in Help and are executable like every other verb. The one exception is
the tag `y` chord, which still mirrors out because a tag is always insert, so
SPC cannot be pressed there, and copying the path out is the whole point of
the chord.

Reading is a new read_clipboard effect answered by an ordinary Event.paste, so
the round trip is honest about being one: SDL and NSPasteboard answer inside
the same drain, the browser answers a promise, and a terminal answers over
OSC 52 or -- far more often -- refuses. A refused read is a paste that does
not happen, and the request dies at the next keystroke rather than landing
minutes late in whatever pane is focused by then.

The tty shell also enables BRACKETED PASTE now and coalesces
paste_start..paste_end into one event. Before this a paste arrived as a flood
of individual key presses: plausible in insert mode, and in normal mode every
pasted character ran as a command.

n/N. They stepped the armed results buffer and immediately Looked each row, so
you could not walk past a hit without opening it. They are a MOTION now:
select the next look-able text, open nothing, and let Enter decide. What they
step is the largest whitespace-delimited run look.resolve can act on
(look.lookableSpan, wrapper punctuation peeled), over a RING of panes -- every
pane that has performed a look, most recent first, then the output buffers
that have not, newest first, and only if both are empty the pane in front of
you. N is the exact inverse of n, computed rather than remembered: both
directions ask the same question about the same spans and compare against the
column the walk parks on, so x presses one way and x back land exactly where
you started, pane boundaries and the ring's seam included.

A ring rather than a list with two ends because a shell's cursor sits at the
prompt, below everything it has printed, so a walk that could not come round
would have nowhere to go on the very first press -- which is the case n/N were
written for.

One motion everywhere, no pane-kind or buffer-kind special case. The only
thing a buffer may change is the GRAIN of what a step selects, and it does it
with one flag rather than a branch: output_pane.Traits.commands (renamed from
`executes`, which named one reader's behaviour rather than the fact) makes a
row select WHOLE, because a ThemeSel line is a word to run and has no path
inside it to pick out. `]d`/`[d` are not n/N -- they are helix's diagnostic
motions, their job is to ARRIVE, and they still reach searchStep.

THE TTY PROMPT. Leaving raw tty blanked the prompt row, and the command you
had typed at that prompt shares the row, so it went too -- a shell out of tty
read as output only. OSC 133 marks the row CELL by cell, so the two are
separable: config.tty_blank = .prompt cuts the prompt's own columns and leaves
the command, left-hugged at column 0 in line with the output under it rather
than in a bay of blanks. .prompt_and_input is the old behaviour, kept.

Because the row is now something you can put a cursor in, enterTty adds the
hidden prompt width back before asking ghostty to walk the shell's own cursor
to it -- the modal column on a cut row is short by exactly that much.

Verified: unit-test 186/186 (nine new), snap 87/87 (new ttyprompt.snap),
hxdiff 481 and hxparity 561 with 0 mismatches, tty and gui both build. And
against the real binaries rather than the harness: in a pty, SPC y emits OSC
52 carrying exactly the selection while plain y emits nothing, SPC p issues
the read and pastes the reply, and a bracketed paste of "dd..." inserts text
instead of deleting two lines. In a real SDL window, SPC y then SPC p round
trips through the system clipboard while the default register holds different
text. Setting tty_blank back to .prompt_and_input reproduces all 86 old
goldens byte for byte.

1 files changed, 14 insertions, 9 deletions

diff --git a/test/snapshots/builtins.snap b/test/snapshots/builtins.snap
index f6b5723b..3b8fb684 100644
--- a/test/snapshots/builtins.snap
+++ b/test/snapshots/builtins.snap
@@ -30,10 +30,12 @@ snap index
 key g e
 stable 700 15000
 snap index-tail
-# n/N here must NOT run the rows. ThemeSel's buffer executes what it steps
-# onto, and that is safe because wearing a theme is free; this list holds Kill,
-# Del and Delcol, so stepping it would end the session. Three presses, and the
-# panes and the listing are all where they were.
+# n/N here run NOTHING, and no longer could: they are a MOTION, and the only
+# thing they do is move the selection onto look-able text. A row here is a key
+# path and a NAME — this list holds Kill, Del and Delcol — and a name is not a
+# path, so the ring finds nothing to stop on in this buffer or in the file
+# above it. Three presses, and the panes and the listing are all where they
+# were. Picking a command is executing its row, two snaps down.
 key n
 key n
 key n
@@ -48,17 +50,20 @@ wait 10000 Right
 stable 700 15000
 snap window-group
 # back to the whole index, and a NAME in it is live text like anywhere else:
-# middle-click `Tutor` and the tutor opens. That is the picking a stepping
-# picker would have done, minus running the rows you passed.
+# middle-click `Tutor` and the tutor opens. That is how a list of commands is
+# picked from — you run the row you want and the ones you passed stay unrun,
+# which is the whole reason n/N were never allowed to be the picker.
 #
 # The one place in this suite a builtin cannot be added for free: the click is
 # a SCREEN coordinate, so every row inserted above `SPC h t` in the listing
-# moves Tutor down one and this number with it.
+# moves Tutor down one and this number with it. The five clipboard builtins
+# put three there — SPC P, SPC R and SPC Y, uppercase sorting ahead of the
+# lowercase `SPC h` — which is why this reads 49 and not 46.
 key space ?
 wait 10000 SPC c n
 stable 700 15000
-press middle 20 46
-release middle 20 46
+press middle 20 49
+release middle 20 49
 wait 10000 PARDES TUTOR
 stable 700 15000
 snap tutor-from-index