summaryrefslogtreecommitdiff
path: root/examples/live/shaders/vm.glsl
Commit message (Collapse)AuthorAge
* examples/live: the language, text in, a tape and a problem outGabriel Schneider2 hours
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lang.compile reads lines of `name = expression` over t, x and y (+ - * /, unary minus, parentheses, numbers, # comments) and returns either a Program, the out and color tapes, or a Problem: a byte of the text and words. The builtins are one table, `builtins` (call, op, arity, value, doc): the survey's sin, cos, exp, log, pow, sqrt, abs, floor, fract, min, max, clamp, mix, step, smoothstep, atan2, noise, saw, sqr, tri, seq, hsv, rgb, tau and pi, and the inputs t, x, y. A name is defined once, before it is used; builtins cannot be renamed; hsv and rgb are colours, so only the whole color line can be one. Each tape is emitted from its line's root, depth first, each term once, so it holds only what the line reaches; t, x and y are a term each however often named, and a negative number is a number. seq's values go in registers side by side: as emitted when they are fresh numbers, else copied. noise's missing arguments are 0. Nothing is allocated: the compiler is a struct on the stack, 512 terms, 128 names, 32 levels of nesting, 17 arguments (seq's 16 values), 128 instructions a tape, about 28 KiB in all; past any of them is a problem in words ("the out line needs more than 128 instructions", at the line). vm.glsl's smoothstep is written out: GLSL leaves lo > hi undefined, and the survey's ring is smoothstep(0.03, 0, ...). Tests: a tone instruction by instruction; the survey's 20-line program (out 54 instructions, color 46, neither holding the other's terms, every operand an earlier register); every builtin; precedence, comments and numbers; 24 problems, each with its byte and words; each capacity, met and passed. zig build test: 6 of 6. Co-Authored-By: Claude Opus 5.5 <[email protected]> Claude-Session: https://claude.ai/code/session_016Y9MNBECMWcJD5pdS4SR6T
* examples/live: the interpreter of a tape, and its probeGabriel Schneider2 hours
Demo 1's route: a program becomes a flat tape of at most 128 instructions (src/Lang.zig: the ops, the instruction, the tape and the two uniform blocks that carry it; build.zig writes Lang.Op out as ops.glsl, so the op numbers have one definition), and ONE interpreter, shaders/vm.glsl, runs it per pixel (picture.frag) and per sample (synth.comp, crossing from the tape it replaces over the first `fade` samples). Instruction i writes register i; the tape is pushed as uniforms. The probe measures it before anything else is built: `zig build probe` plays made-up tapes (every instruction reaching the last, a noise in ten) under --profile-gpu. RTX 3050 (driver 620.70.06), Debug host, means of 601 frames, three runs agreeing within 0.07 ms: picture, empty tape 720p 0.14-0.23 1080p 0.19-0.28 (a pass's cost) picture, 60 720p 1.38-1.45 1080p 2.89-2.96 picture, 128 720p 2.71-2.81 1080p 5.86-5.95 picture, 128 at 640x360 0.85-0.94 The budget, under 2 ms at 1280x720: 60 instructions meet it, 128 do not. The cheap fixes, on 128 at 720p: the tape in a storage buffer 2.97-3.03 (worse); the registers as an array of 16 (kept in registers, indexing turned into selects) 5.82-5.93 (twice as slow); the 128-array with only 16 slots used 2.11-2.34 (cache footprint: a register allocator would buy about a sixth); half resolution 0.85-0.94. So the sketch will draw a tape longer than 64 instructions at half resolution, scaled up. The variants are kept outside the tree. The synth's numbers taken here were of a kernel that wrote nothing (its uniform block was past SDL's 4 KiB): the sound's change measures it again. Co-Authored-By: Claude Opus 5.5 <[email protected]> Claude-Session: https://claude.ai/code/session_016Y9MNBECMWcJD5pdS4SR6T